For a long service life.

emco clean-off mats are robust and durable. Cleaning and care are also quick and easy! Most emco clean-off mats are designed so that the majority of the dirt falls through the gaps into the mat well.

Nevertheless: Regular care and cleaning improves the cleaning performance and prolongs the service life of your emco clean-off mat. emco goes even further in simplifying the cleaning of your entrance mat!

In the case of light soiling, clean the mat with a vacuum cleaner set to strong suction, depending on the amount of use. We recommend daily cleaning with a vacuum cleaner, In the case of medium soiling, roll up the mat and also clean the mat and the mat well with a broom after rolling up. If you have large mat system that are also extremely heavy, it is recommended to roll the mat up from one side up to the middle and clean. Then roll up the other side to the middle and clean. We recommend this is done weekly, with the mat well also being cleaned. In the case of heavy soiling, remove the whole mat from the mat well and clean the top with a pressure washer (distance at least 30cm) in a suitable place. The water temperature should not be more than 60°C. After a suitable drying time (depending on the weather), replace the mat that has been raised. We recommend cleaning with a pressure washer one a month.

Entrance mats with textile inserts, such as ribbed carpet, Care, Conform, Maximus, Innova or Outdoor can be cleaned easily with a vacuum cleaner or pressure washer. See Cleaning entrance mats in general. The following tips will help to make cleaning the insert even more effective.

  1. Use a brush vacuum cleaner! A powerful brush vacuum cleaner should be used for entrance mats with textile inserts. Vacuum cleaners with one or two brush rolls remove the dirt right down to the substrate material. At the same time, the brushes life the insert upright again and keep it “open” to new dirt.
  2. The right cleaning products! Use a neutral cleaning product*. Never use solvents based on chlorinated hydrocarbons! In the case of heavy soiling, a cleaning product can be applied to the mat with the pressure washer prior to cleaning and carefully worked in with a brush. The cleaning product can also be added to the pressure washer water. Please rinse with clear water afterwards.
  3. Remove stains! Treat stains as early as possible as some substances can cause permanent damage to fibres and inks. How quickly you act will determine how successfully the mat can be cleaned. Nearly 80% of all fresh stains can be removed with clean water. Sponge off and absorb liquids with a towel (or something similar). Concentrated, dried-in substances such as chewing gum must be loosened (e.g. with a scraper) and brushed out. Water-soluble stains should be remoistened with a little water and sponged off. Please note that stains must be sponged off and not rubbed in. Always work from the outer edges inwards to avoid making the stains bigger. Repeat this process if necessary. If you are not able to remove stubborn stains using this method, contact us for recommendations of suitable products.

Entrance mats with brushes can be easily cleaned with a vacuum cleaner or a pressure washer. See Cleaning entrance mats in general. The following tips will help to make cleaning even more effective.

  1. Without a brush vacuum cleaner! Brush vacuum cleaners on a brush insert generate friction that blocks the vacuum cleaner’s roller. Therefore, don’t use a brush vacuum cleaner and use a vacuum cleaner without a rotating roller.
  2. Scrubbing brush! Especially stubborn, fixed dirt can be brushed out with a scrubbing brush. To do this, brush the dirt out of the entrance mat aluminium profile in an upwards direction.

Entrance mats with rubber inserts can be easily cleaned with a vacuum cleaner or a pressure washer. See Cleaning entrance mats in general.

When using cleaning products, warm water with a neutral cleaning product* can be used. Please rinse off with clear water afterwards. Never use cleaners containing solvents!

Remove coarse dirt, such as leaves and sand, from dirt collection wells. Take out the grid, clean it and reinsert it after cleaning.

Dirt collection wells with a drain can be easily cleaned with a pressure washer. A neutral cleaner* or citric acid* should be used for stubborn or extremely stubborn dirt. Apply the cleaner to a cloth and treat the place affected by rubbing vigorously. Please rinse with clear water afterwards. Never use steel wool or abrasive sponges.

Dirt collection wells without a drainage system should not be cleaned with a pressure washer because of the standing water. Please use a neutral cleaner*. Apply the cleaner to a cloth and thoroughly wipe the dirt collection well. Remove any cleaner residue immediately with a damp cloth (with clear water). Never use steel wool or abrasive sponges.

Our installation frames are anodised in a natural colour (FAQ). Please use an anodic cleaning product*. Apply the cleaner to a cloth and treat the place affected by rubbing vigorously. Then buff with a dry cloth. Never use acidic or alkaline products! Never use steel wool or abrasive sponges.

Ramp edges wells with a drain can be easily cleaned with a pressure washer. A neutral cleaner* or citric acid* should be used for stubborn or extremely stubborn dirt. Apply the cleaner to a cloth and treat the place affected by rubbing vigorously. Please rinse off with clear water afterwards. Buff with a dry cloth. Never use steel wool or abrasive sponges.

Anodised profiles (FAQ) can be easily cleaned with a pressure washer. See Cleaning entrance mats in general.

The following tips will help to make cleaning even more effective.

  1. The right cleaning products! Please use an anodic cleaning product*. Apply the cleaner to a cloth and treat the place affected by rubbing vigorously. Then buff with a dry cloth. Never use acidic or alkaline products!
  2. Remove salt deposits! De-icing salts are no problem for anodised products. Nevertheless, there may be white residues on the profile that are visible, especially on dark anodised products. Apply some neutral cleaner to a cloth and treat the affected places.. Then buff with a dry cloth.
  3. Make minor repairs! Contact with dirt and small stones can lead to small scratches on the anodised material. An anodise touch-up pen can be used for the repair. Test it on a place that is not visible. There is only limited availability of colours from specialist retailers.

Just like the entire entrance mat, emco Inox can be easily cleaned with a pressure washer. See Cleaning entrance mats in general. The following tips will help to make cleaning even more effective.

emco Inox is made of stainless steel. The inner surface is painted. For stubborn dirt, use a neutral cleaner*. Apply the cleaner to a cloth and treat the place affected by rubbing vigorously. Then rinse off with clear water afterwards. Buff with a dry cloth. Never use steel wool or abrasive sponges. Never use acidic or alkaline products! They could damage the paint.

Just like the entire entrance mat, emco SpinSafe can be easily cleaned with a pressure washer. See Cleaning entrance mats in general. The following tips will help to make cleaning even more effective.

The tactile surface and the attention panels are made of stainless steel. A neutral cleaner* or citric acid* should be used for stubborn or extremely stubborn dirt. Apply the cleaner to a cloth and treat the place affected by rubbng vigorously. Then rinse off with clear water afterwards. Buff with a dry cloth. Never use steel wool or abrasive sponges. Never use acidic or alkaline products!

Entrance mat systems that exceed a defined total weight or a certain profile length are supplied in sections.
The following criteria apply to this:

Maximum section weights
Overall height: 12mm 25 kg
Overall height: above 17mm 30 kg

In addition, there is a maximum section depth of 2,000mm for all entrance mats.

For an entrance mat system in several pieces, the sections are arranged in the mat well on the basis of the position numbers on the back of the mat. They are directly after the order number and contain information on the section number and the total number of sections. Abbildung XX, which also describes the laying of the mat sections, illustrates this. Arrangement of the entrance mat system starts at the bottom left and ends at the top right.

In the case of manufacture on the basis of drawings, this requirement for positioning the stickers and end rolls does not necessarily apply!

Cleaning clean-off mats
in three simple steps:

Light soiling

Vacuum once a day: depending on usage levels, your emco entrance mat should be cleaned every day with a brush vacuum cleaner. This will remove light soiling.

Medium soiling

Sweep once a week: after vacuuming and rolling up the mat, simply sweep clean the underside and the mat well with a broom. This will remove the collected dirt.

Heavy soiling

Wash once a month: after thorough cleaning, treat with a pressure washer. Lay the mat again after a short drying time. Alternatively, use a standard floor cleaning machine.

Our service

The experience gained from more than 60 years of entrance mat production gives us an expertise that guarantees success from the start. The advantages are clear:

  • Best possible result from the start
  • Avoidance of costly and time-consuming changes
  • Professional solutions to specific problems
  • Speedy service availability throughout Germany

Whether consulting, measuring and installation service, condition inspections or spare parts service: with us, you decide when you need us.

* The cleaning product manufacturer’s instructions for use and dosage must be strictly adhered to.

Contact

Your contact for renovation & renewal

contact Form - Refit

Achim Holzapfel

20 years of expertise for the entrance area

Note

We do not accept any liability for damage resulting from failure to observe these cleaning and care instructions or from improper use of emco products.